Other

COMPATIBLE WITH THE FOLLOWING ONEUP GUIDES - CHAIN GUIDE - ISCG05 - V2 - BASH GUIDE - ISCG05 - V2 - E-BIKE - STEPS/EP8 - Kit includes 1 two piece top guide

A BETTER REMOTE FOR ANY CABLE OPERATED DROPPER An Aluminum remote with an oversized bearing and a super smooth action. The unique lever position allows you to keep a stronger grip on the bars while actuating your post. Don't think twice about dropping your post, even when charging into technical sections. The OneUp lever mimics your R/H shifter’s inboard upshift paddle position instead of the usual downshift paddle position of most remotes. This position requires considerably less thumb movement to reach the lever. NO BLEEDING The cable setup is quick and easy. The cable clamps at the lever making shortening the housing length for clean routing a breeze. Unlike a hydraulically actuated dropper, there is no temperature sensitivity and If your remote gets damaged you can still lower or extend your post by removing it from your frame and pushing on the actuator by hand. - Kit includes cable and housing - Compatible with all cable actuated dropper posts.

This kit includes all the parts required to rebuild your V2 Dropper Post. - Replacement Seal - Upper and lower bushings - Anti-rotation pins - Compatible with V2 Dropper Post ONLY.

Replacement dropper post remote clamp. Can be used to convert existing clamp on the OneUp Dropper Remote. - Compatible with Shimano I-Spec EV (M9100, M8100, M7100) brake mounts. - Does not contain remote body.

Replacement dropper post remote clamp. Can be used to convert existing clamp on the OneUp Dropper Remote. - Compatible with SRAM MatchMakerX (MMX) or Shimano I-Spec EV (M9100) brake mounts. - Does not contain remote body.

Set of six oversized pins. All dropper posts require key way clearance. With so many different frames, clamps and ride heights it's not possible to ship play-free without running the risk of binding. The kit is meant to remove additional play that might develop over time or, for the more mechanically inclined, to tune the play out for a specific bike. Start with the 3 pins marked with 2 lines. If play still exists move to the 3 pins marked with 4 lines.

The EDC Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer. Top caps are compatible with all 1-1/8" aluminum steerer tubes. The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. KIT INCLUDES - EDC TOP CAP - EDC steerer plug - 2x 1mm, 3mm, & 5mm Headset Spacers

SWITCH. A QUICK-CHANGE DIRECT MOUNT CHAINRING SYSTEM FROM ONEUP COMPONENTS. Switch was developed to reduce the cost of replacement chainrings, increase compatibility with new offsets and to make the process of changing your chainring much faster and simpler. - Cheaper Replacement Cost - Replacement rings are a fraction of the cost of a complete direct mount chainring - Quick Change - Replace your ring in less than an minute, using only a 4mm hex key. Tailor your gearing to the terrain that you're riding - Enduro World Series Champion Winning Narrow Wide tooth profile keeps your chain in place on the roughest terrain - 4 Ring Sizes (28, 30, 32, 34T) - 2 Profiles - both Round and Oval - 12 speed ring designed to work with both Shimano Hypergilde+ 12 speed chains and SRAM Eagle 12 speed chains. - Get ultimate traction with Oval rings by smoothing out the torque you deliver to your rear tire - 3 Offsets - Regular, Boost and Super Boost - Quick Change Rings can be replaced in less than a minute with only a 4mm allen key, without removing your crank. Simply loosen the bolts 2 turns, unlock the ring by rotating it by 20 degrees and pull it over and off your crank. Reverse these steps to install your new ring. If you plan to ride a trail that you know is steeper than your local trails, you can switch to a smaller ring in the parking lot, in less time than it takes your friend to put on his riding shoes! SPECS - Material: 7075-T6 - Weight: 66g (30T Boost Oval) Chainline: - 6mm offset - 49mm GXP/BB30 Long Spindle - 3mm offset - 52mm (Boost) GXP/BB30 Long Spindle - 0mm/SB - 49mm BB30 Short spindle, 56mm GXP/BB30 Long Spindle Compatibility: SRAM DM cranks; 9, 10, 11 and 12 Speed Chains